Topic: FMC150 Configuration  (Read 10246 times)

Frank November 28, 2014, 04:05 AM

  • Member
  • *
  • Posts: 3
     Hello,professor,I need your help!


     I want to use ML605 to configurate the FMC150,


So can you tell me where I can download the reference


design?VHDL or Verilog is ok.


    Thank you.

arnaudNL December 01, 2014, 06:50 AM (#1)

  • 4DSP Staff (EU)
  • Administrator
  • Member
  • *****
  • Posts: 7110
Frank,


The reference design is part of the BSP, you can register your products and obtain a bsp from http://www.4dsp.com/fmc/bsp


This location is printed on the packaging of all our FMC boards.


Best Regards,
Arnaud



Frank December 02, 2014, 04:28 AM (#2)

  • Member
  • *
  • Posts: 3



Thank you for your reply,I have downloaded the BSP already.


When I used the FMC Analyzer,I met some questions.


I used the Ethernet to connect ML605 with computer, but the


software showed there was no device connected.So I cannot open the FMC150 using the software.


Secondly, what I want is the original VHDL or Verilog program of ML605_FMC150.bit,so can you give it to me?



arnaudNL December 02, 2014, 05:48 AM (#3)

  • 4DSP Staff (EU)
  • Administrator
  • Member
  • *****
  • Posts: 7110
Frank,


Have you found the 4FM Getting Started Guide already (C:\Program Files (x86)\4dsp\4FM Core Development Kit\Documentation\4FM_Get_Started_Guide.pdf) ?


The document explains what is StellarIP: Chapter 4.2
The document indicates where the StellarIP firmwares are installed: Chapter 4.5
The document explains how to load a firmware in StellarIP and create an ISE project: Chapter 5.1.1 to 5.1.4
The document indicates that Ethernet based reference design cannot be used in the GUI on chapter 4.9
The document explains how to use the Analyzer: Chapter 4.9.5
The document explain how to run the reference software: Chapter 11.


I hope that helps!


Best Regards,
Arnaud

arnaudNL December 03, 2014, 07:23 AM (#4)

  • 4DSP Staff (EU)
  • Administrator
  • Member
  • *****
  • Posts: 7110
Dear Frank,


Was the information useful, are you able to move forward?


Best Regards,
Arnaud

Frank December 04, 2014, 03:41 AM (#5)

  • Member
  • *
  • Posts: 3
OK,Thank you for your reply.


Maybe I need more time to figure it out.

arnaudNL December 04, 2014, 05:28 AM (#6)

  • 4DSP Staff (EU)
  • Administrator
  • Member
  • *****
  • Posts: 7110
Dear Frank,


No problem I leave this topic open for the time being.


Best Regards,
Arnaud

arnaudNL December 11, 2014, 08:23 AM (#7)

  • 4DSP Staff (EU)
  • Administrator
  • Member
  • *****
  • Posts: 7110
Dear Frank,


I am following up with you. Where are we at, are you able to move forward?


Best Regards,
Arnaud

arnaudNL December 15, 2014, 06:43 AM (#8)

  • 4DSP Staff (EU)
  • Administrator
  • Member
  • *****
  • Posts: 7110
Dear Frank,


I will close this topic in 24 hours unless I get some news from you.


Best Regards,
Arnaud

arnaudNL December 16, 2014, 11:50 AM (#9)

  • 4DSP Staff (EU)
  • Administrator
  • Member
  • *****
  • Posts: 7110
This topic is being closed because the issue is considered as resolved by 4DSP. Feel free to create a new topic for any further inquiries.