FMC - FPGA Mezzanine Card

FMC-LPC Analog-to-Digital Converter Board
Multi-Channel Multi-Mode 8-bit ADC
1.25 Gsps / 2.5 Gsps
FMC VITA 57.1 Compliant

  • Description

      The FMC122 is a Dual-Channel Multi-Mode A/D FMC, fully compliant with VITA 57.1 Standards. The card provides two 8-bit ADC channels that enable simultaneous sampling of 2 or 1 channel with a maximum sample rate of 1.25 GSPS (2-channel mode) or 2.5 GSPS (1-channel mode).

      The sample clock can be supplied externally through a coax connection or supplied by an internal clock source (optionally locked to an external reference). Additionally a trigger input for customized sampling control is available.

      The FMC122 daughter card is mechanically and electrically compliant to the FMC standard as established by ANSI/VITA 57.1. The FMC122 has a has a LPC (low-pin count) compatible connector, front panel I/O, and can be used in a conduction cooled environment.

      The design is based on the E2V Quad A/D EV8AQ160 chip-set having DDR LVDS outputs. The analog signal inputs are available on the front panel on coax connections and have individual calibration circuits for fine-tuning of gain, offset, and phase.

      The FMC122 allows flexible control on clock source, sampling frequency, and calibration through the I2C serial communication bus. Furthermore the card is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions.

  • Features
      Dual – Single 8-Bit Channel Operation
      2-Channel 1.25 Gsps A/D conversion Mode
      1-channel 2.50 Gsps A/D conversion Mode (calibration package required, option –C48 to be added to P/N)
      VITA 57.1-2010 compliant.
      Conduction Cooled
      1.25Gsps or 625Msps DDR LVDS outputs
      Coax front panel inputs on SSMC connectors
      Single ended AC-coupled analog input.
      Flexible clock tree enables:
      internal clock
      external clock
      Mil-I-46058c Conformal Coating Compliant (optional)
      LPC (low-pin count) compatible

      (Click Block Diagram to Enlarge)

      FMC122 Block Diagram
      FMC122 Block Diagram

  • Board Support Package
      4FM GUI offers multiple functions including the ability to monitor voltage and temperature; perform memory tests; measure the PCIe bandwidth; update FPGA firmware; and access StellarIP
      StellarIP available for this product. A simple way to design FPGA firmware with automated code and bitstream generation
      Data analyzer makes it possible to display digitized data real time
      Reference designs that work out of the box are available for multiple platforms, please see tables below
      Can be used on any VITA 57.1 compliant carrier card
      User Manual
      For support, please visit our support forum
      Download the BSP datasheet for more information
  • Application
      Direct RF Down Conversion
      Software defined radio (SDR)
      Ultra Wideband Satellite Digital Receiver
      Medical equipment
      Aerospace and test measurement instruments

      FMC122 Performance Chart

  • Performance
      Selectable analog input range (500mVpp / 625mVpp)
      Selectable input bandwidth (500MHz / 600MHz / 1.5GHz / 2.0GHz)
      Individual Gain control (±18%)
      Individual Offset control (±50mV)
      Individual Phase control (±14ps)
      > 60dB channel isolation (crosstalk)

      The FMC122 comes with an integrated Cross Point Switch allowing flexible mapping of analog inputs to the converters. Unused converters can be placed in standby mode or a full standby mode can place all channels in power saving mode.

      With the build in DMUX feature of the FMC122 it is possible to adapt the digital output interface to the carrier hardware. When the DMUX feature is enabled each channel has a 16-bit Double Data Rate LVDS bus at 625Mbps (full speed sampling). Without de-multiplexing the digital output interface compromises two 8-bit DDR LVDS busses at 1.25Gbps.

  • Environmental
      Operating Temperature0C to +55C0C to +55C
      Storage Temperature-40C to +85C-40C to +85C
      Operating Vibration5Hz to 100Hz, PSD = 0.04g2/Hz

      100Hz to 1000Hz PSD = 0.04 gs^2/Hz

      1000Hz to 2000Hz PSD decreasing at 6 dB/ octave
      5Hz to 100Hz PSD increasing at 3 dB/ octave

      100Hz to 1000Hz PSD = 0.1 g^2/Hz

      1000Hz to 2000Hz PSD decreasing at 6 dB/octave
      Operating Shock20g, 11 millisecond, half-sine or 20g, 11 millisecond, terminal sawtooth shock pulses in all three axes40g, 11 millisecond shock half-sine or 40g, 11 millisecond, terminal sawtooth shock pulses in all three axes
      Operating Altitude-1500 ft to 60,000 ft
      (with airflow)
      -1500 ft to 60,000 ft
      Conformal CoatingOptionalOptional

Talk to us about your algorithmic requirements, 4DSP is a full-service firmware and software development house. We are specialists at high performance FFT and Video Processing. Check with us, we may have IP Cores that meet requirements for your application, right off the shelf.